新闻中心
EVA hot melt adhesive is currently one of the widely used industrial adhesives. They are essentially thermoplastic based on polymers, which means they are solid at room temperature but liquefy when exposed to a heat source.
In this article, you will learn more about hot melt adhesive: EVA hot melt adhesive. What issues should be noted when using?
Do you use different types of hot melt adhesives to bind different types of paper?
Sure, ordinary paper can be bound with ordinary hot melt adhesive and copperplate paper adhesive. Copperplate paper adhesive needs to be bound with copperplate paper; The glue pot of the wireless glue installation machine should use glue that has been open for a long time.
(Note: The opening time of hot melt adhesive refers to the time when the glue solidifies, which is generally 6-13 seconds.). )
2. How long should finished books be stored before cutting?
Cutting should be carried out during the cooling, hardening, and forming process of hot melt adhesive. Generally, this time should be kept at least 3 minutes, otherwise problems such as spine deformation and adhesive sticking may occur.
(Note: The cooling and hardening time of EVA hot melt adhesive is generally more than 3 minutes)
3、 How should the temperature of the glue tank be adjusted?
Firstly, the technical specifications provided by the Sunlife hot melt adhesive manufacturer must be followed. Too high or too low will reduce the adhesive strength and tensile strength. Therefore, the temperature of the hot melt adhesive particles must be controlled within a certain range to achieve adhesion.
In addition, the temperature of the adhesive should vary depending on the quality of the paper. For example, the inorganic content in copperplate paper is about 10 times higher than that in adhesive paper and writing paper. Inorganic substances have good thermal conductivity and can accelerate the cooling of hot melt adhesive particles;. The curing speed, so in this case, the temperature of the glue pot should be slightly increased.
What are the requirements for the use environment of EVA hot melt adhesive?
In general, maintaining a temperature of 20-25 ℃ and a humidity of around 50% can achieve the bonding effect.
5、 How long does it take for books and magazines to be delivered for use?
Usually shipped immediately at a digital printing store. Of course, there is no problem with regular use, but don’t read too much at this time because the bonding effect of EVA hot melt adhesive is only achieved after 24 hours.
6、 What are the common reasons for users to drop pages during use?
In addition to the issues mentioned above, it is usually necessary to pay attention to whether the equipment debugging is appropriate and whether the operation method is correct. Another easily overlooked issue is the addition of many adhesive particles at once during the operation process. However, due to the small workload each time, repeated heating and melting of EVA hot melt adhesive can damage the structure of the macromolecular chain and reduce heat generation. The viscosity of the melt. This situation is quite common in digital printing shops.
7、 Can edge glue and back glue be mixed?
Not recommended for mixed use. The fluidity of edge glue is higher than that of backing glue. Using edge glue as backing glue will make the book’s backing glue uneven and prone to empty glue. Back glue cannot be used as edge glue either.
8、 Why does transparent adhesive turn yellow?
Excessive temperature and prolonged repeated heating can cause the glue to turn yellow.
Solution: Reduce the temperature of the adhesive tank. When using hot melt adhesive particles at once, do not add too much. Use according to the amount and dosage, and if it is not enough, add more.
The importance of product packaging is twofold: it helps maintain the safety and reliability of the contents and provides consumers with attractive products. The packaging process is one of the most important stages in product manufacturing and distribution. With decades of experience as a packaging hot melt adhesive manufacturer, Sunlife Hot Melt Adhesive is delighted […]
Determine whether the material used to make the box is the same as before, and whether the surface has been treated, such as copperplate paper, with completely different properties from the original one. The performance differences of hot melt adhesives for the same purpose in the market are not significant. It will be difficult to […]
Hot melt adhesive granulesCan I customize the color myself? Sure, but it depends on the purpose. If it is to adjust the color of the adhesive layer (such as using a specific color adhesive for the inner lining of a gift box), a legitimate manufacturer blends the color masterbatch with the base material before granulation […]
There are various types of hot melt adhesives with different uses and compositions, generally classified according to their chemical composition and uses. 1、 Polyolefin hot melt adhesive Polyolefin hot melt adhesives include polyethylene hot melt adhesive and polypropylene hot melt adhesive. Polyethylene (PE)is polymerized from ethylene with a small amount of alpha olefin or other […]